It is currently Thu, 29 Oct 2020 12:26:30 GMT



 
Author Message
 Mixing UDMA33/66 drives, VIA IDE, Linux 2.2.18
Hello,

        I've run into a problem while using the follwing different drives:
IBM-DTTA-351010 and IBM-DJNA-351520. The first one is a UDMA33 drive and the
second one seems to be a UDMA66 capable drive, UDMA4. I have attached a
"hdparm -i" of both drives at the end of the mail.

        Both drives are connected to the same IDE channel on a VIA686A board
with a 80pin IDE cable. When I try to access the UDMA33 drive I get:

Mar  2 16:08:30 kiza kernel: hda: irq timeout: status=0x58 { DriveReady
SeekComplete DataRequest }
Mar  2 16:08:41 kiza kernel: hda: timeout waiting for DMA
Mar  2 16:08:41 kiza kernel: hda: irq timeout: status=0x58 { DriveReady
SeekComplete DataRequest }
Mar  2 16:08:51 kiza kernel: hda: timeout waiting for DMA
Mar  2 16:08:51 kiza kernel: hda: irq timeout: status=0x58 { DriveReady
SeekComplete DataRequest }
Mar  2 16:09:01 kiza kernel: hda: timeout waiting for DMA
Mar  2 16:09:01 kiza kernel: hda: irq timeout: status=0x58 { DriveReady
SeekComplete DataRequest }
Mar  2 16:09:01 kiza kernel: hda: DMA disabled
Mar  2 16:09:01 kiza kernel: hdb: DMA disabled
Mar  2 16:09:01 kiza kernel: ide0: reset: success

        and the system continues to work with DMA disabled.

        If I use a 40pin cable to connect the drives there are no problems. If
I try to set -X66 with hdparm for the UDMA66 disk (that should set UDMA33
mode, right?) and use the 80 pin cable the problem is not solved.

        The problem seems to be the 80 pin cable. Can't the drives operate in
different modes independently? Setting a slower transfer mode with hdparm does
not work. Can it be set otherwise? With a kernel parameter?

        I'm using 2.2.18 with the IDE driver that came with it. Is this maybe
a problem that was solved in 2.4?

        Or is it just a theoretical "that will not work" problem? :)

Thanks for any help.

Oliver

Output of hdparm -i for both drives. Both are connected with a 40pin cable
this time:

 Model=IBM-DTTA-351010, FwRev=T56OA73A, SerialNo=WF0KFTR8113
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
 BuffType=DualPortCache, BuffSize=466kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=19807200
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes: pio0 pio1 pio2 pio3 pio4
 DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2

 Model=IBM-DJNA-351520, FwRev=J56OA30K, SerialNo=G80GLW69191
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
 BuffType=DualPortCache, BuffSize=430kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=30033360
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes: pio0 pio1 pio2 pio3 pio4
 DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4

--
Oliver Feiler                                               k...@gmx.net
http://www.**-**.com/ ~kiza/pgpkey              PGP key ID: 0x561D4FD2
http://www.**-**.com/ ~kiza/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at   http://www.**-**.com/
Please read the FAQ at   http://www.**-**.com/



 Wed, 20 Aug 2003 00:20:04 GMT   
 
   [ 1 post ] 

Similar Threads

1. 2.2.18 IDE tape problem, with ide-scsi

2. 2.2.18 IDE tape problem, with ide-scsi

3. 2.2.18 IDE tape problem, with ide-scsi

4. VIA 82c586b in UDMA33 mode (2.2.19 + ide)?

5. Largest IDE under 2.2.18?

6. kernel 2.2.18 + ide patch panics when trying to mount root fs

7. bad block locks IDE on 2.2.18?

8. 2.2.18 corruption: IDE + PCMCIA ?

9. IDE drives question - UDMA 66?

10. SCSI and IDE hard drives mixed for Linux?


 
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by ST Software