It is currently Sat, 24 Oct 2020 09:39:23 GMT



 
Author Message
 PROBLEM: Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)
[1.] One line summary of the problem:    
Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)

[2.] Full description of the problem/report:

Dual (2) AMD ATHLON MP 1900+ CPUs
ASUA7M266D Motherboard
2 sticks of  Corsair CM72SD512R-2100 (1Gb RAM)

When booting SMP-Kernels version 2.4.7, 2.4.9, 2.4.18 the box hangs with the
following error:

APIC error on CPU1: 00(02)
APIC error on CPU0: 00(02)

Durning the POST I get this, but do not know if it means anything.

CPU0 AMD ATHLONG (TM) MP 1900+
CPU1 *AMD ATHLONG (TM) MP 1900+

Not sure what the asterick means.

Complete message on the screen follows prior to lockup:

CPU0 AMD ATHLON (TM) XP 1900+ stepping 02
per CPU timeslice cutoff: 731.19 usecs
task migration cache decay timeout: 10 msecs
enabled ExtINT on CPU #0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU #1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop...3198.15 BogoMIPS
CPU: L1 I Cache: 64K (64 bytes/lines, Dcache 64 (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/lines)
Intel machine check reporting enabled on CPU #1
CPU1: AMD ATHLON (TM) XP 1900+ stepping 02
total of 2 processors activated (6389.76 BogoMIPS)
Enabling IO-APIC IRQs
Setting 2 in the phy_id_present_map
... chaning IO-APIC physical APIC ID to 2...ok
... TIMER vector 0x31 ping1=2 pin2=0
testing the IO APIC ...................................... done.
Using ocal APIC timer interrupts.
Calibrating APIC timer...
... CPU clock speed is 1600.0830 Mhz.
... host bus clock speed is 266.687 Mhz.
CPU: 0, clocks: 2666804, slice: 888934
CPUO <T0:2666800, T1:1777856, D:10, S:888934, C:2666804>
CPU: 1, clocks: 2666804, slice: 888934
CPU1 <T0:2666800, T1:8889286, D:4, S:888934, C:2666804>

[3.] Keywords (i.e., modules, networking, kernel):
kernel, SMP, Athlon

[4.] Kernel version (from /proc/version):
2.4.18

[5.] Output of Oops.. message (if applicable) with symbolic information
     resolved (see Documentation/oops-tracing.txt)
N/A

[6.] A small shell script or example program which triggers the
     problem (if possible)

[7.] Environment
Dual (2) AMD ATHLON MP 1900+ CPUs
ASUA7M266D Motherboard
2 sticks of  Corsair CM72SD512R-2100 (1Gb RAM)

[7.1.] Software (add the output of the ver_linux script here)
Machine does not boot far enough to run the ver_linux. Here is the output when
booted under 2.4.18 non-SMP version.

Linux samurai 2.4.18 #1 Thu Apr 25 09:19:44 CDT 2002 i686 unknown

Gnu C                  2.96
Gnu make               3.79.1
binutils               2.11.90.0.8
util-linux             2.11f
mount                  2.11g
modutils               2.4.13
e2fsprogs              1.26
reiserfsprogs          3.x.0j
Linux C Library        2.2.4
Dynamic linker (ldd)   2.2.4
Procps                 2.0.7
Net-tools              1.60
Console-tools          0.3.3
Sh-utils               2.0.11
Modules Loaded         tulip iptable_nat ipt_REJECT ipt_LOG ipt_state
ip_conntrack iptable_filter ip_tables ide-scsi scsi_mod ide-cd cdrom usb-ohci
usbcore ext3 jbd

[7.2.] Processor information (from /proc/cpuinfo):

Since I'm under a non-SMP, only 1 CPU shows.

processor       : 0
vendor_id       : AuthenticAMD
cpu family      : 6
model           : 6
model name      : AMD Athlon(TM) XP 1900+
stepping        : 2
cpu MHz         : 1600.111
cache size      : 256 KB
fdiv_bug        : no
hlt_bug         : no
f00f_bug        : no
coma_bug        : no
fpu             : yes
fpu_exception   : yes
cpuid level     : 1
wp              : yes
flags           : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips        : 3191.60

[7.3.] Module information (from /proc/modules):

tulip                  43968   1
iptable_nat            20852   0 (autoclean) (unused)
ipt_REJECT              4064   0 (autoclean)
ipt_LOG                 5568   0 (autoclean)
ipt_state               1504   0 (autoclean)
ip_conntrack           21196   2 (autoclean) [iptable_nat ipt_state]
iptable_filter          2784   0 (autoclean)
ip_tables              14112   7 [iptable_nat ipt_REJECT ipt_LOG ipt_state
iptable_filter]
ide-scsi               10176   0
scsi_mod              119948   1 [ide-scsi]
ide-cd                 35424   0
cdrom                  34400   0 [ide-cd]
usb-ohci               21376   0 (unused)
usbcore                74592   1 [usb-ohci]
ext3                   69600   1
jbd                    50336   1 [ext3]

[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(auto)
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
a000-afff : PCI Bus #02
  a400-a4ff : Lite-On Communications Inc LNE100TX
    a400-a4ff : tulip
  a800-a8ff : C-Media Electronics Inc CM8738
b800-b80f : Advanced Micro Devices [AMD] AMD-768 [??] IDE
  b800-b807 : ide0
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(auto)
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
a000-afff : PCI Bus #02
  a400-a4ff : Lite-On Communications Inc LNE100TX
    a400-a4ff : tulip
  a800-a8ff : C-Media Electronics Inc CM8738
b800-b80f : Advanced Micro Devices [AMD] AMD-768 [??] IDE
  b800-b807 : ide0
  b808-b80f : ide1
d000-dfff : PCI Bus #01
  d800-d87f : Silicon Integrated Systems [SiS] 86C326
e800-e803 : PCI device 1022:700c (Advanced Micro Devices [AMD])

00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-3ffebfff : System RAM
  00100000-00224fff : Kernel code
  00225000-002e8fff : Kernel data
3ffec000-3ffeefff : ACPI Tables
3ffef000-3fffefff : reserved
3ffff000-3fffffff : ACPI Non-volatile Storage
f7800000-f9ffffff : PCI Bus #02
  f7800000-f78000ff : PCI device 1033:00e0 (NEC Corporation)
  f8000000-f8000fff : NEC Corporation USB (#2)
    f8000000-f8000fff : usb-ohci
  f8800000-f8800fff : NEC Corporation USB
    f8800000-f8800fff : usb-ohci
  f9000000-f90000ff : Lite-On Communications Inc LNE100TX
    f9000000-f90000ff : tulip
fa000000-fadfffff : PCI Bus #01
  fa000000-fa00ffff : Silicon Integrated Systems [SiS] 86C326
fae00000-faefffff : PCI Bus #02
faf00000-fb7fffff : PCI Bus #01
  00100000-00224fff : Kernel code
  00225000-002e8fff : Kernel data
3ffec000-3ffeefff : ACPI Tables
3ffef000-3fffefff : reserved
3ffff000-3fffffff : ACPI Non-volatile Storage
f7800000-f9ffffff : PCI Bus #02
  f7800000-f78000ff : PCI device 1033:00e0 (NEC Corporation)
  f8000000-f8000fff : NEC Corporation USB (#2)
    f8000000-f8000fff : usb-ohci
  f8800000-f8800fff : NEC Corporation USB
    f8800000-f8800fff : usb-ohci
  f9000000-f90000ff : Lite-On Communications Inc LNE100TX
    f9000000-f90000ff : tulip
fa000000-fadfffff : PCI Bus #01
  fa000000-fa00ffff : Silicon Integrated Systems [SiS] 86C326
fae00000-faefffff : PCI Bus #02
faf00000-fb7fffff : PCI Bus #01
  fb000000-fb7fffff : Silicon Integrated Systems [SiS] 86C326
fb800000-fb800fff : PCI device 1022:700c (Advanced Micro Devices [AMD])
fc000000-fdffffff : PCI device 1022:700c (Advanced Micro Devices [AMD])
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
ffff0000-ffffffff : reserved

[7.5.] PCI information ('lspci -vvv' as root)

00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700c (rev 11)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 32
        Region 0: Memory at fc000000 (32-bit, prefetchable) [size=32M]
        Region 1: Memory at fb800000 (32-bit, prefetchable) [size=4K]
        Region 2: I/O ports at e800 [disabled] [size=4]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2
                Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700d (prog-if
00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: fa000000-fadfffff
        Prefetchable memory behind bridge: faf00000-fb7fffff
        BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-

00:07.0 ISA bridge: Advanced Micro Devices [AMD]: Unknown device 7440 (rev 04)
        Subsystem: Asustek Computer, Inc.: Unknown device 8044
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:07.1 IDE interface: Advanced Micro Devices [AMD]: Unknown device 7441 (rev
04) (prog-if 8a [Master SecP PriP])
        Subsystem: Advanced Micro Devices [AMD]: Unknown device 7441
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Region 4: I/O ports at b800 [size=16]

00:07.3 Bridge: Advanced Micro Devices [AMD]: Unknown device 7443 (rev 03)
        Subsystem: Asustek Computer, Inc.: Unknown device 8044
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- ...

read more »



 Wed, 13 Oct 2004 10:40:07 GMT   
 PROBLEM: Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)
Quoting Bob Tanner (tan...@real-time.com):

<snip>

<snip>

Thanks to Jerry McBride, I think the problem is this.

The BIOS reports the CPUs as MP, but the kernel detects them as XP. As Jerry
pointed out you can't run dual XP processors.

I just grabbed the box the CPUs came in. It states the CPUs are MP.

How can I tell if the problem is with the BIOS, CPUs or kernel?

--
Bob Tanner <tan...@real-time.com>         | Phone : (952)943-8700
http://www.mn-linux.org, Minnesota, Linux | Fax   : (952)943-8500
Key fingerprint =  6C E9 51 4F D5 3E 4C 66 62 A9 10 E5 35 85 39 D9

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/



 Wed, 13 Oct 2004 11:50:05 GMT   
 PROBLEM: Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)
 > I just grabbed the box the CPUs came in. It states the CPUs are MP.
 > How can I tell if the problem is with the BIOS, CPUs or kernel?

ftp://ftp.suse.com/pub/people/davej/x86info/

x86info with no arguments will tell you what it thinks the CPU is
(it does MP/XP discrimination), and what the CPU reports itself as
(The processor name string)

x86info -f will tell you the CPU capability flags lines,
which should show an 'mp' bit on MP CPUs.

Note btw, grab v1.9. 1.8 had a stupid bug which broke AMD recognition.
I only just uploaded it so you may have to wait 30 mins for the
mirror script to kick in.

    Dave.

--
| Dave Jones.        http://www.codemonkey.org.uk
| SuSE Labs
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/



 Wed, 13 Oct 2004 19:00:09 GMT   
 PROBLEM: Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)

We get the strings by asking the CPU what they are. The BIOS loads the
values into the CPU
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/



 Wed, 13 Oct 2004 23:10:10 GMT   
 PROBLEM: Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)

Either update the BIOS or set it to MP1.1
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/



 Wed, 13 Oct 2004 23:10:12 GMT   
 PROBLEM: Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)

Which BIOS version was the problem found on? I've got one of these,
and the original 1004 Award BIOS didn't give this problem, nor does
the 1005A BIOS I upgraded to.

However, I am having memory problems. Anyone else got similar
experiences (or good experiences)? I got 3 of 1 GiB DDR266 ECC Reg
DIMMs (36 chips apiece) and a 512 MiB DDR266 ECC Unbuf DIMM (18
chips). I have various problems:

- none of the DIMMs are reported by the BIOS as ECC, whether plugged
  in together or separately

- plugging in one 1 GiB DIMM will sometimes yield a bit error with
  memtest86 test #1

- plugging in two 1 GiB DIMMs will yield a bit error in test #1

- plugging in three 1 GiB DIMMs will yield a stream of bit errors in
  test #1 (and possibly other tests, but I gave up before then).

The vendor claims the 1 GiB DIMMs are compatible with the A7M266-D,
but when I received the M/B and DIMMs, I noted the motherboard manual
said it only supported DIMMs with up to 18 chips each, and of course
the 1 GiB DIMMs have 36 chips each :-(

According to Asus tech support 18 chip 1 GiB DIMMs are not available
yet. When I asked why they claimed support for 1 GiB DIMMs, they said
"for the future". Argh! Anybody know if 18 chip 1 GiB DDR DIMMs are
available anywhere?

                                Regards,

                                        Richard....
Permanent: rgo...@atnf.csiro.au
Current:   rgo...@ras.ucalgary.ca
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/



 Wed, 13 Oct 2004 23:30:15 GMT   
 PROBLEM: Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)
The behavior you originally described, and the bootup output (where the
kernel reports the CPUs as XPs) might indicate you're really running XPs.

Especially the part where the system runs fine when only 1 CPU is
installed. That's what a lot of XP users report.

I know you checked the box, but maybe to be sure you can emove the heatsink
(make sure you have spare thermal compound handy for when you replace it)
and check on the core, is it a 1900XP or 1900MP.

I have several Tyan 2466N and 2466N-4M and all report the CPUs as 1900+ MPs
when the kernel boots.

Another user reported stability issues that turned out to be his MP CPUs.
He was able to move them to other motherboards and cause the stability
problems. In the end he had to swap CPUs. I'll ask him to email you
directly perhaps he can help. He has your motherboard as well.

****************************************************
Nicolae P. Costescu, Ph.D.  / Senior Developer
Stronghold Technologies
46040 Center Oak Plaza, Suite 160 / Sterling, Va 20166
Tel: 571-434-1472 / Fax: 571-434-1478

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/



 Thu, 14 Oct 2004 00:40:08 GMT   
 PROBLEM: Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)
Hi Bob,

I had the same problem with a Tyan S2466N, except that
the system didn't crash.  It would intermittently
throw off these non-fatal APIC errors.  Using 2.4.18 I
was able to trigger an error storm just by running an
fft benchmark.

The problem seems to have been fixed by upgrading the
ROM BIOS to the most recent (beta) version.

Regards,
Lew Wolfgang

<snip>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/



 Thu, 14 Oct 2004 09:50:07 GMT   
 PROBLEM: Dual (2) AMD ATHLON MP 1900+ CPUs gives APIC error on CPU[0]: 00(02)
Hi Bob,

I've got exactly the same problem with a similar configuration (Athlon
MP 2000+ instead)

For information, the PC was shipped with Win XP pro installed and it
worked fine (two athlons running)

When I tried to install Redhat7.3, I ran into the same trouble.

No solution found yet, but I've mailed AMD and redhat with questions
and reports.

I'll keep you posted.

Benji



 Tue, 26 Oct 2004 18:59:07 GMT   
 
   [ 13 post ] 

Similar Threads

1. Dual Athlon MP 1900+ on MSI K7D Master-L

2. APIC error on CPU:00(08) ?

3. APIC error on CPU0: 00(02)

4. Do not taint AMD non-MP cpus if only one cpu is present

5. AMD Athlon 1900+ and Memory Problems

6. 2èathlon mp 1900 vs athlon 64 x2 ???

7. SOLVED : LILO gives me L 00 00 00 00 00 00 00

8. Help LILO gives me L 00 00 00 00 00 00 00

9. Solaris upgrade 10/00 to 02/02 possible?

10. Q: Configure 2 CPU MP Machine as 1 CPU


 
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by ST Software