I just installed linuxppp 2000 Q4 on a Beige G3 with a ZIF G4 upgrade
processor (500 MHz) and a four port USB PCI card.  I have an ADB mouse and a
logitech USB wheel mouse attached to the Mac.  The boot log is shown below:

The ADB mouse works fine but I can't get the USB mouse to work at all.  Does
someone know how to get the USB mouse configured or can you direct me to
documentation that might tell me how?

Also, I got my X display to work at higher color resolution by putting 15
into the depth for the monitor.  When I put in 16 or 24 the display crashes.
Only 15 seems to work.  Any suggestions about how to configure XF86Config?
When I use Xconfigurator it doesn't work.  Is there another configuration
tool for XF86Config?  How do I tell which version of Xfree that I'm using?

Otherwise, the system is nearly up and running perfectly.  I'd like to
remove sendmail from the startup services, and I'd like to configure the
system to recognize a laserprinter which I have attached to the ethernet
port of the Mac.  Any help with these issues???

Thanks.

device tree used 47964 bytes
Total memory = 256MB; using 1024kB for hash table (at c0300000)
Linux version 2.2.18-4hpmac (r...@entropy.crashing.org) (gcc version 2.95.3
20001220 (prerelease/franzo/20001220)) #1 Thu Dec 21 15:16:15 MST 2000
PCI bus 0 controlled by pci at 80000000
Registered 1 feature controller(s)
pmac nvram is core99: 0
System has 64 possible interrupts
GMT Delta read from XPRAM: -300 minutes, DST: on
via_calibrate_decr: decrementer_count = 167073 (1002439 ticks)
Console: colour dummy device 80x25
Calibrating delay loop... 999.42 BogoMIPS
Memory: 255876k available (1408k kernel code, 4708k data, 152k init)
[c0000000,d0000000]
Dentry hash table entries: 32768 (order 6, 256k)
Buffer cache hash table entries: 262144 (order 8, 1024k)
Page cache hash table entries: 65536 (order 6, 256k)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
adb devices: [2]: 2 2 [3]: 3 32 [15]: 3 1
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 262144 bhash 65536)
Starting kswapd v 1.5
clgen: Driver for Cirrus Logic based graphic boards, v1.5.2
 Couldn't find PCI device
MacOS display is /pci/ATY,mach64_3DUPro
atyfb: 3D RAGE PRO (PQFP, PCI) [0x4750 rev 0x7c] 6M SGRAM, 14.31818 MHz
XTAL, 230 MHz PLL, 100 Mhz MCLK
BUS_CNTL DAC_CNTL MEM_CNTL EXT_MEM_CNTL CRTC_GEN_CNTL DSP_CONFIG DSP_ON_OFF
6b2ea040 87010182 08651a79 e0130c01     03000600      001807ee   03c007cf
PLL ad d5 21 64 e4 03 81 e6 8e 9e 98 01 a6 1b 00 00
atyfb: monitor sense=717, maps to mode 12
Console: switching to colour frame buffer device 128x48
fb0: ATY Mach64 frame buffer device on /pci/ATY,mach64_3DUPro
input0: Macintosh mouse button emulation
PowerMac Z8530 serial driver version 2.0
tty00 at 0xf3013020 (irq = 15) is a Z8530 ESCC, port = modem
tty01 at 0xf3013000 (irq = 16) is a Z8530 ESCC, port = printer
pty: 256 Unix98 ptys configured
Macintosh non-volatile memory driver v1.0
pmac_ide: enabling IDE bus ID 0
pmac_ide: enabling IDE bus ID 1
hdc: MATSHITA CR-587, ATAPI CDROM drive
hdd: TOSHIBA DVD-ROM SD-R1002, ATAPI CDROM drive
ide1 at 0xf5021000-0xf5021007,0xf5021160 on irq 14
fd0: SWIM3 floppy controller
sym53c8xx: at PCI bus 0, device 13, function 0
sym53c8xx: setting PCI_COMMAND_IO...
sym53c8xx: 53c875 detected
sym53c875-0: rev 0x4 on pci bus 0 device 13 function 0 irq 23
sym53c875-0: ID 7, Fast-20, Parity Checking
ncr53c8xx: at PCI bus 0, device 13, function 0
ncr53c8xx: IO region 0x10000[0..127] is in use
scsi0 : sym53c8xx-1.7.1-20000726
scsi1 : MESH
scsi : 2 hosts.
  Vendor: IBM       Model: DDRS-39130W       Rev: S92A
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
  Vendor: QUANTUM   Model: XP39100J          Rev: LYK8
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
mesh: target 4 synchronous at 5.0 MB/s
  Vendor: iomega    Model: jaz 1GB           Rev: J.83
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi removable disk sdc at scsi1, channel 0, id 4, lun 0
scsi : detected 3 SCSI disks total.
sym53c875-0-<0,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 15)
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17850000 [8715 MB] [8.7
GB]
sym53c875-0-<1,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 16)
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17781520 [8682 MB] [8.7
GB]
sdc : READ CAPACITY failed.
sdc : status = 0, message = 00, host = 0, driver = 08
sdc : extended sense code = 2
sdc : block size assumed to be 512 bytes, disk size 1GB.
eth0: BMAC at 00:05:02:07:e2:8e
3c59x.c 15Sep00 Donald Becker and others
http://www.**-**.com/
Partition check:
 sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7
 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8 sdb9
 sdc:scsidisk I/O error: dev 08:20, sector 0
 unable to read partition table
ADB keyboard at 2, handler set to 3
Detected ADB keyboard, type ANSI.
input1: ADB HID on ID 2:2.02
ADB mouse at 3, handler 1
input2: ADB HID on ID 3:3.32
ADB mouse at 15, handler set to 4 (TurboMouse 5)
input3: ADB HID on ID 15:3.01
event0: Event device for input3
event1: Event device for input2
event2: Event device for input1
event3: Event device for input0
usb.c: registered new driver hid
keybdev.c: Adding keyboard: input1
mouse0: PS/2 mouse device for input3
mouse1: PS/2 mouse device for input2
mouse2: PS/2 mouse device for input0
mice: PS/2 mouse device common for all mice
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xd480e000, IRQ 0
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 1 port detected
usb-ohci.c: USB OHCI at membase 0xd4810000, IRQ 0
usb.c: new USB bus registered, assigned bus number 2
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 1 port detected
usb-ohci.c: USB OHCI at membase 0xd4812000, IRQ 0
usb.c: new USB bus registered, assigned bus number 3
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 1 port detected
usb-ohci.c: USB OHCI at membase 0xd4814000, IRQ 0
usb.c: new USB bus registered, assigned bus number 4
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 1 port detected
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 152k init 28k prep
usb.c: USB new device connect, assigned device number 2
usb_control/bulk_msg: timeout
usb-ohci.c: unlink URB timeout!
usb.c: USB device not accepting new address (error=-110)
usb.c: USB new device connect, assigned device number -1
usb.c: USB device not accepting new address (error=-12)
usb.c: USB disconnect on device -1
grep uses obsolete /proc/pci interface
usb.c: USB new device connect, assigned device number 2
usb_control/bulk_msg: timeout
usb-ohci.c: unlink URB timeout!
usb.c: USB device not accepting new address (error=-110)
usb.c: USB new device connect, assigned device number -1
usb.c: USB device not accepting new address (error=-12)
usb.c: USB disconnect on device -1
DMA sound driver installed, using 4 buffers of 32k.
CSLIP: code copyright 1989 Regents of the University of California
PPP: version 2.3.7 (demand dialling)
PPP line discipline registered.
NET4: AppleTalk 0.18 for Linux NET4.0
invalid vmode
registered device ppp0
PPP BSD Compression module registered
PPP Deflate Compression module registered

I'm not a Linux expert, but I see your kernel is a little bit old. I know
that earlier kernel didn't support USB very well: maybe you can try with a
newer one.

"Stephen D. Scotti, M.D." <sdsco...@earthlink.net> wrote in message
news:B7F118C5.2226%sdscotti@earthlink.net...